Monocrystalline silicon pressure transmitter
The monocrystalline silicon pressure transmitter a
- Tel：18019899982
- Fax：0550-7989666
- Mail：tkjd@tiankang.com
Description
I. usage
The monocrystalline silicon pressure transmitter adopts high accuracy, high overvoltage and strong stability of monocrystalline silicon sensor technology, embedded intelligent powerful signal processing module, realize different temperature automatic compensation, not affected by temperature and high overpressure, improve the comprehensive measurement accuracy and long-term stability of the site. Intelligent integrated design of transmitter, equipped with liquid crystal display and keypad, can transfer positive and negative points without pressure source, set range and damping time, and improve on-site adjustment function of products. Widely used in various industrial automatic control environment, involving water conservancy and hydropower, railway transportation, intelligent building, production automation, aerospace, military, petrochemical, oil wells, power, ships, machine tools, pipes, medical, food and many other industries.
Two, characteristics
1. High accuracy, high overvoltage and strong stability of monocrystalline silicon technology
2, the current 4mA to 20mA current superposition HART communication protocol.
3, 5 digit LCD digital display, internal and external three buttons, shortcut operation, local adjustment function.
4, positive and negative pressure zero point migration, range can be set, no need for linearity adjustment.
5, Pa, kPa, MPa, bar, mbar,%, psi, mmH2O and other different display units.
6, instrument self diagnosis function, automatic temperature compensation.
Three, technical parameters
medium | Liquid, gas, steam |
range | Any range (single crystal silicon pressure sensor) in -100KP-0-60MPa |
Accuracy grade | Level 0.075 |
output | 4-20mA, 4-20Ma+HART protocol |
Medium temperature | -30~+85 C |
ambient temperature | -20~+85 C |
Power supply voltage | DC24V |
Load resistance | 0-600 ohm (DC24V) Note: at least 250 ohms of load resistance when communicating with handheld communicator. |
Saturation current | Upper bound 20.8mA lower limit 3.8mA |
Alarm current | Upper limit 22.8mA lower limit 3.6mA (mode can be set) |
Adjustment function | The zero point and full range point can be adjusted from the top three buttons on the top of the shell, with local adjustment, or configuration software can be used for remote adjustment. |
Zero point migration | It can migrate within a wide range of -20%~+20%. |
Nonlinear | + 0.2%F.S |
Hysteresis and repeatability | + 0.1%F.S |
Annual long term stability | + 0.1%F.S |
Thermal zero drift | + 0.02%F.S |
response time | Less than 50ms |
Working pressure | 1.5 times range |
Electrical connection | Connection terminal |
Process connection | External thread (M20*1.5, G1/2, 1/2NPT, etc.) Flange (DN25, DN40, etc.) Chuck |
External component material | 304 stainless steel /316L stainless steel |
Shell material | Cast aluminum housing |
Protection level | IP65 |
Four, specification type
EBY-KD | Monocrystalline silicon pressure transmitter | ||||||
O- | No explosion proof | ||||||
B- | explosion-proof | ||||||
P | Protective cast aluminum housing | ||||||
H | Standard Hester joint | ||||||
A | 4-20mA current output tape display | ||||||
A1 | 0-10mA current output without display | ||||||
V1 | 0-5V voltage output | ||||||
V2 | 0-10V voltage output | ||||||
R | RS485 | ||||||
HA | With HART communication superimposed 4-20mA output | ||||||
G- | Gauge pressure | ||||||
A | Absolute pressure | ||||||
Z | LCD display (4-20mA output only) | ||||||
E | LED display (4-20mA output only) | ||||||
G | Thread (default M20 * 1.5, other specification notes) | ||||||
F | Flange installation (DN25, DN40, etc.) | ||||||
W | Chuck installation | ||||||
Browse：
